I bought this Marshall 6100 30th Anniversary amp back in the early 1990’s new, so it’s about 25 years old. It’s kind of the father of the JVM heads we have now. 3 channels (lead, crunch, clean) with different settings on each channel. Channels are switchable by MIDI. The crunch channel 2 has three different modes: A = JTM 45’ish, B = Super Lead / JCM800’ish, C = JCM900’ish and these profiles here are from that channel’s modes B and C. My version is the 6100B with EL34’s and black tolex, no Lead-Mod (aka -LM version).
The poweramp can operate in Pentode and Triode mode, where the Triode mode has half the power (50W) and sounds a bit warmer than the more modern sounding Pentode mode.
The cabinet is a 1990’s Mesa Rectifier Slant 4×12 where I have installed a Celestion G12-T75 besides the stock Vintage 30’s (British). The mics were my trusty Shure SM57 and my new Sennheiser e906 which is pretty great btw. These went into a BAE 1073MP preamp. The amp gets power through a Furman power conditioner.
My profile chain is always all analog.
The profiles can be found on the Rig Exchange by searching for “RiF-30th”.
My filename-coding is as follows:
RiF-30th Ch[channel-number][channel-mode]-[t for triode, p for pentode][brightness level][speaker][mic]
Example: “RiF-30th Ch2.B-t2 T75 906” = Channel 2, Mode B, Triode, Brightness level 2, T75 speaker, e906 microphone
I made sure that the filenames are short enough to see any relevant differences in the KPA’s browser.
The brightness level goes from 1-3 , where 2 is what I consider “normal”. 1 is darker and 3 is brighter. The difference in brightness is usually achieved by moving the microphone.
Too much bass? Turn down the BASS on the main screen slighty. Go down in 0.3 dB steps.
Too much highs? Try one of the other profiles with a lower number or turn down the TREBLE knob on the main screen. Try values < 1 dB. The gain on the mode C profiles is pretty high and I left the original setting in the profile for authenticity, but I suggest to turn down the gain quite a bit. On the other hand, the mode B profiles can benefit from some added gain. FX SECTION: The EQ in the FX section makes the tone somehow "mix ready". A 70Hz low- and 10KHz high-cut plus a little notch at 4KHz to get rid of some harsh highs. It's off by default. The reverb is a small ambience which I think suits this kind of tone very well. STOMP SECTION: Noise Gate, Green Screamer, Graphic EQ and Treble Booster (try this if you're playing a neck-position humbucker). All off by default. THE SOUND SAMPLES Here are some short clips. The guitars are louder than in a normal mix so you can hear them clearly. All guitar tracks have been recording directly from the Kemper's STACK output. So there aren't any FX on the guitars. Even in Pro Tools they are kept bone dry. All clips have been recorded with a Gibson Les Paul Standard with a Duncan JB at the bridge position. THE PICTURES Here are some picture of the gear and the settings / mic positions used for the profiles. Marshall 6100: kemper-amps.com/wbb_suite_3/index.php?attachment/7479/ kemper-amps.com/wbb_suite_3/index.php?attachment/7478/ kemper-amps.com/wbb_suite_3/index.php?attachment/7477/ Celestion Vintage 30: kemper-amps.com/wbb_suite_3/index.php?attachment/7480/ Celestion G12-T75: kemper-amps.com/wbb_suite_3/index.php?attachment/7475/ Shure SM57: kemper-amps.com/wbb_suite_3/index.php?attachment/7476/ Sennheiser e906: kemper-amps.com/wbb_suite_3/index.php?attachment/7474/ As always, I appreciate any feedback (positive or negative) from you guys!